 |
| Quantity: | |
|---|---|
Size: 2400 x 1200 x 17mm/ 1800 x 1200 x 17mm
HC
4412330090
| Construction: | Panel code: 17-10-11 17 mm nominal thickness 1.0 mm face veneer 11 plies |
| Film: | 60/ 165 g/m2 black phenolic resin coating, 2 sides |
| Glue bond: | Phenolic resin. A-bond. |
| Edge seal: | Edges are sealed with 2 layer acrylic paint |
| Stress Grade: | F17, Applies in both the parallel and perpendicular directions to the grain. |
| Standard: | AS 6669 - 2007 Plywood - Formwork |
| Finish: | Capable of a Class 2 off-form finish on first pour when used in conjunction with good site and formwork practices and AS 3610 (subject to conditions). |
| Formaldehyde Emission: | Super E0 |
| Environmental: | Bsi Benchmark Certified |
| Tolerances: | Thickness: +/- 0.5 mm Squareness: +/- 1.0 mm |
| Stress Grade | Nominal Thickness (mm) | Dimension (mm) | Weight (kg/sheet) | Parallel to face grain | Perpendicular to face grain | Packing Unit (sheets) | ||
| Moment of inertia | Section modulus | Moment of inertia | Section modulus | |||||
| I (mm4 /mm) | Z (mm3 /mm) | I (mm4 /mm) | Z (mm3 /mm) | |||||
| F17 | 17 | 1800 x 1200 | 23 | 230.0 | 26.8 | 176.0 | 22.5 | 40 |
| F17 | 17 | 2400 x 1200 | 31 | 230.0 | 26.8 | 176.0 | 22.5 | 50 |
HongCheng Formply is a high quality film faced plywood developed and engineered specifically for the Australian market. With a three tier quality control program comprising; a detailed 'Manufacturing Specification' adhered to by trained staff; more than ten years experience quaily control teams; and regular, detailed and recorded in laboratory testing on key quality requirements. HongCheng Formply provides assurance of quality and consistency.
How to cut the the best from HongCheng film faced plywood?
Storage
Always clean and repair the formwork panels before storage, the formwork should then be stacked off the ground on level supports and under cover. framed formwork panels should be stacked alternately face and back to back to avoid face damage by bolts etc. if panels are wet, do not allow them to dry too rapidly.
Sealing of edges
Phenolic film faced plywood edges are fully sealed by the factory and it is the most important that all edges remain sealed. to obtain full value from a phenolic film faced plywood sheet any recut edges should sealed as soon as possible with water proof paint sealing of holes.
any hole made in film faced formwork panels should also be sealed to prevent water entering. if water does enter it may cause swelling around the holes.
Cleaning and repair
To obtain full life, cleaning should be carried out immediately after each use. phenolic film faced plywood may be wiped with release agent or cleaned with water and stiffbrush. it may be necessary to use a hard wood scraper but care should be taken not to damage the plywood face. do no use a wire brush or sharp metal scraper to dislodge hardened concrete.
| Construction: | Panel code: 17-10-11 17 mm nominal thickness 1.0 mm face veneer 11 plies |
| Film: | 60/ 165 g/m2 black phenolic resin coating, 2 sides |
| Glue bond: | Phenolic resin. A-bond. |
| Edge seal: | Edges are sealed with 2 layer acrylic paint |
| Stress Grade: | F17, Applies in both the parallel and perpendicular directions to the grain. |
| Standard: | AS 6669 - 2007 Plywood - Formwork |
| Finish: | Capable of a Class 2 off-form finish on first pour when used in conjunction with good site and formwork practices and AS 3610 (subject to conditions). |
| Formaldehyde Emission: | Super E0 |
| Environmental: | Bsi Benchmark Certified |
| Tolerances: | Thickness: +/- 0.5 mm Squareness: +/- 1.0 mm |
| Stress Grade | Nominal Thickness (mm) | Dimension (mm) | Weight (kg/sheet) | Parallel to face grain | Perpendicular to face grain | Packing Unit (sheets) | ||
| Moment of inertia | Section modulus | Moment of inertia | Section modulus | |||||
| I (mm4 /mm) | Z (mm3 /mm) | I (mm4 /mm) | Z (mm3 /mm) | |||||
| F17 | 17 | 1800 x 1200 | 23 | 230.0 | 26.8 | 176.0 | 22.5 | 40 |
| F17 | 17 | 2400 x 1200 | 31 | 230.0 | 26.8 | 176.0 | 22.5 | 50 |
HongCheng Formply is a high quality film faced plywood developed and engineered specifically for the Australian market. With a three tier quality control program comprising; a detailed 'Manufacturing Specification' adhered to by trained staff; more than ten years experience quaily control teams; and regular, detailed and recorded in laboratory testing on key quality requirements. HongCheng Formply provides assurance of quality and consistency.
How to cut the the best from HongCheng film faced plywood?
Storage
Always clean and repair the formwork panels before storage, the formwork should then be stacked off the ground on level supports and under cover. framed formwork panels should be stacked alternately face and back to back to avoid face damage by bolts etc. if panels are wet, do not allow them to dry too rapidly.
Sealing of edges
Phenolic film faced plywood edges are fully sealed by the factory and it is the most important that all edges remain sealed. to obtain full value from a phenolic film faced plywood sheet any recut edges should sealed as soon as possible with water proof paint sealing of holes.
any hole made in film faced formwork panels should also be sealed to prevent water entering. if water does enter it may cause swelling around the holes.
Cleaning and repair
To obtain full life, cleaning should be carried out immediately after each use. phenolic film faced plywood may be wiped with release agent or cleaned with water and stiffbrush. it may be necessary to use a hard wood scraper but care should be taken not to damage the plywood face. do no use a wire brush or sharp metal scraper to dislodge hardened concrete.